Adapting a W58 gearbox to your 4AG

DjSpecter · Post by **DjSpecter** » Tue Apr 28, 2009 11:27 pm

SWEET EXECELENCE!!!!!!!!!!!!!!!!

kevlar corolla · Post by **kevlar corolla** » Wed Apr 29, 2009 8:37 pm

Installed the tranny tonight,bolted up just like a stocker-made me very happy.

Once I bolted the starter in I couldn't resist the urge to see if it would run,hasn't since last september.

I was amazed that it fired and ran very well,don't think it would've turned more than 1 revolution before it was running-a good night all around. :D

Ricky86 · Post by **Ricky86** » Thu Apr 30, 2009 9:01 am

Awesome plate dude!!!

kevlar corolla · Post by **kevlar corolla** » Sun May 03, 2009 7:59 am

Only 1 left!!.

Post by **dr.occa** » Sun May 03, 2009 9:34 am

kevlar corolla wrote:Only 1 left!!.

i'm not surprised!

let me know shipping if any when you're shipping 'em out. thanks again for this tom!

kevlar corolla · Post by **kevlar corolla** » Tue May 19, 2009 5:14 pm

Ok so the suckers are finally finished,should be picking them up tomorrow night after work and shipping by weeks end.

I do still have 1 left,I won't be having any other made-too many headaches.

Post by **dr.occa** » Wed May 20, 2009 7:49 am

kevlar corolla wrote:Ok so the suckers are finally finished,should be picking them up tomorrow night after work and shipping by weeks end.

that's great to hear tom!

kevlar corolla wrote: ...I won't be having any other made-too many headaches.

sorry it was a PITA of a project.

kevlar corolla · Post by **kevlar corolla** » Wed May 20, 2009 7:42 pm

The only real pita was I wasn't making them as its beyond what I'm capable of and having to rely on others to do as they said they would.

Will be shipping out soon.

Tom

kevlar corolla · Post by **kevlar corolla** » Sat May 23, 2009 6:02 pm

The parts were shipped today,unfortunately they wouldn't let me ship it cod so I've paid shipping for the ones I've sold.

dr.occa the shipping costs were $30 cdn,which works out too $28 us funds.If you need my paypal again just let me know.

Thanks.

Post by **dr.occa** » Sun May 24, 2009 9:04 pm

kevlar corolla wrote:The parts were shipped today,unfortunately they wouldn't let me ship it cod so I've paid shipping for the ones I've sold.

dr.occa the shipping costs were $30 cdn,which works out too $28 us funds.If you need my paypal again just let me know.

Thanks.

thank you tom! payment sent good sir.

kevlar corolla · Post by **kevlar corolla** » Mon May 25, 2009 8:18 pm

Thanks Jonas.

kevlar corolla · Post by **kevlar corolla** » Mon May 25, 2009 9:09 pm

Just sold the last one,makes me very happy.

Post by **nt66** » Mon Mar 01, 2010 6:52 pm

hey jonas where did you find the azcustoms guy? I emailed him and i'm waiting for a reply. Just from looking at the pictures and comparing az's to kevlars I think azcustoms adapter is the correct rotation.

mooreofit · Post by **mooreofit** » Mon Mar 01, 2010 10:25 pm

i thought you already had a w58 will?

Post by **nt66** » Tue Mar 02, 2010 12:09 am

no i've been running a t50 since the beginning but I just got a w58. I also got the adapter plate from jonas that came from kevlar. I installed it but the hole placement rotates the trans about 20 degrees to the drivers side which won't work for me.

if you look at this picture when the t50 bellhousing is bolted up the flat part with the little notch in it will be parallel to the ground which put the shifter at a retarded angle.

basically for it to sit correctly these two red lines need to be perpendicular

on another note with this trans setup there is no need for a custom drive shaft or trans tunnel work. You just need the front yoke that goes with the w58 the shafts and trannies are the same length

www.86garage.com

Adapting a W58 gearbox to your 4AG

Re: Adapting a W58 gearbox to your 4AG

Re: Adapting a W58 gearbox to your 4AG

Re: Adapting a W58 gearbox to your 4AG